L/R

Headphone Test

Check that your headphones, earbuds or speakers play the left and right channels correctly, sound centred, and cover the full frequency range. Every sound is generated on this page. No microphone, no download.

Protect your hearing. Sounds start quiet. Put your headphones on, play a test, then raise the volume slowly. Stop if anything is uncomfortable.

20%

Sets the level of the test sounds only; your device volume still applies. Press Esc to stop any sound.

Choose a test below.

Left and right

Each sound should come only from the side named.

Stereo and polarity

The sweep should travel smoothly. "In phase" should sound focused, "out of phase" wide and vague.

Frequency range

A tone glides from 20 Hz (deep bass) to 20 kHz (highest treble) in 20 seconds. Press Mark when you first hear it and again when it fades out. Don't raise the volume to hear the extremes.

Frequency: –

How to test your headphones

  1. Lower your device volume, put your headphones on (left earpiece on the left ear; it is usually marked L), and press Left.
  2. Raise the volume gradually until the sound is clear but comfortable, then try Right and Both. "Both" should sound centred and equally loud on each side.
  3. Play the left-to-right sweep. The sound should travel smoothly from one ear to the other, with no jump or hole in the middle.
  4. Compare In phase and Out of phase. This is mostly useful for speakers and for headphones you have repaired or re-cabled.
  5. Run the frequency sweep to hear how low and how high your headphones go, or play single tones to check for rattles and buzzing.

What the results mean

Left and right are swapped

Check that the earpieces are on the right ears. If they are, the swap usually comes from a software setting (some audio apps and "spatial audio" modes remap channels), an adapter, or a wiring fault in a repaired cable.

Sound comes from both sides when only one is selected

Your device is probably set to mono audio, an accessibility option that mixes both channels together. Bluetooth headsets can also fall back to a mono "hands-free" mode while a call or video-call app holds the microphone. Close those apps and reconnect the headset.

One side is quiet or silent

First check the balance setting (see below). If it is centred, try another cable, socket or device. A side that crackles or cuts out when you move the cable points to a damaged wire or plug. For earbuds, also clean the mesh and check that each bud is charged and connected.

In phase and out of phase sound the same, or the reverse

With correctly wired headphones or speakers, the in-phase version sounds focused in the centre and the out-of-phase version sounds wide and vague, with less bass. If it is the other way round, one speaker or one earpiece is wired with reversed polarity: swap the + and − wires on one side.

Frequency range

Most headphones play from well below 40 Hz, and small speakers often fade out between 60 and 150 Hz. At the top, the limit is usually your ears, not your headphones: many adults stop hearing somewhere between 12 and 17 kHz, and that limit drops with age. Low tones also sound quieter than mid tones at the same level, which is normal.

Fix balance and mono settings

Windows 11

Settings → System → Sound, choose your headphones, then check that the Left channel and Right channel sliders match. Mono audio is in Settings → Accessibility → Audio.

macOS

System Settings → Sound → Output, select your headphones and centre the Balance slider. Mono is under System Settings → Accessibility → Audio ("Play stereo audio as mono").

iPhone and iPad

Settings → Accessibility → Audio & Visual: turn off Mono Audio and centre the Balance slider.

Android

Look for Settings → Accessibility → Audio adjustment (or Hearing enhancements on Samsung) for the mono audio switch and the left/right balance. The exact names vary by manufacturer.

Listening safely

Loud sound can damage hearing permanently, and the risk grows with both level and listening time. A common rule of thumb is to keep headphones below about 60% of the maximum volume. Test tones are more tiring than music, so keep the test volume modest and the tests short. This page starts every session at a low level and caps the test signals below full scale, but your device volume still decides how loud they are.

This is a check for your headphones, not a hearing test. If you notice ringing, muffled hearing or a difference between your ears, see a hearing professional.

Privacy

The test sounds are calculated by your browser while you listen. The page does not use your microphone, downloads no audio files and sends nothing about your device or your results.

Frequently asked questions

Why can't I hear anything on my iPhone?

Check the volume buttons and that the headphones are connected. On older iOS versions, the ring/silent switch can mute sound played by web pages: switch it to ring and try again.

Does it work with speakers?

Yes. Sit centred between the speakers. The left/right and polarity tests are especially useful after connecting speaker wires.

Why does the left sound come from both earbuds?

Mono audio is probably on, or the headset is in its hands-free mode during a call. See Fix balance and mono settings above.

Is the frequency sweep accurate?

The page generates the frequencies exactly, but what you hear also depends on your device's sound processing, your headphones and your ears. Use it to compare, not as a measurement.

Do Bluetooth headphones add a delay?

Yes, often 100 to 300 milliseconds. It doesn't affect this test, but it explains lip-sync issues in videos and games.

Testing a headset?

Check its microphone too with the microphone test, then convert recordings privately: M4A to MP3, WAV to MP3.